LED Outdoor Lighting - Results Page 35 (2024)

FAQs

What is the common problem with LED lights? ›

Flickering and dimming issues with LED lighting can be a concern for users. Low quality LED bulbs and drivers are more likely to experience flickering issues. Problems can also occur in high-quality lights if mistakes are made in the installation process. Another cause for this issue is loose electrical connections.

One common reason LED lights may not turn on is due to a faulty power source. Please check if your LED lights are plugged in and that the power source is functioning normally. Additionally, check the power cord for damages or loose connections. Another reason LED lights may not turn on is due to a faulty LED bulb.

Check the Connections: Inspect all connections for any loose wires or corrosion. Poor connections often result in issues such as flickering or dead LEDs. 3.) Inspect the Power Supply: Test your LED Driver is functioning correctly and providing the appropriate voltage and current.

Lumens are the measure of light output. The number of lumens needed for outdoor lighting depends on the purpose and location of the light. For example, a porch light may require 800-1000 lumens, while a floodlight may need 2000-3000 lumens. For pathway lighting, 100-200 lumens per light are sufficient.

Many basic LED light fixture designs incorporate the LED driver into the design for convenience. However, the drivers themselves generate heat and are also adversely affected by heat. Bolting them to a hot heatsink is about the worst treatment they can get and subsequently this causes premature failures.

LED lights are made to run constantly for a long time without overheating or causing any safety risks. They are much safer than conventional incandescent lights, which if left on for an extended period of time can get hot and possibly start a fire.

This tiny button can be found on the main control box or on the light strip itself. Once you locate it, all you need to do is press and hold the button for a few seconds until the light flashes. That's it! Your LED strip light is now reset and ready to go.

LED bulbs don't generate as much heat as other bulbs, but that does mean they can be a little sensitive to overheating. This can cause them to burn out too quickly. Keep your bulbs cool and they'll last longer. Firstly, ensure the bulbs you're using aren't too big for the fitting.

On average, LED lights can last up to 50,000 hours. That's approximately 50 times longer than a typical incandescent bulb and 20-25 times longer than a typical halogen bulb. This translates to about 11 years of continuous operation or 22 years of 50% operation.

You can find shorts in outdoor lighting by looking for wires that are cut, broken, frayed, are improperly connected, or are stretched by roots or rocks. We'd also look for bad, wet, corroded, or damaged sockets. We'd be checking for any areas that could be exposing wires or bulbs to moisture too.

Why are only a few of my LED lights working? ›

The most common reason LED lights stop working is a faulty power source. You should check to make sure your lights are plugged in and the power source is working normally (you can check this by plugging something else into the outlet and seeing if it switches on), or purchase a new LED power supply.

LED Keeper is a special tool that fixes LED string lights with a broken circuit. It pierces the insulation of the wiring and connects the copper within the set wires on LED strings. Doing so creates a new electrical current that bypasses the damage in the wire.

40 watts is the ideal amount of brightness for outdoor areas at home. People can see clearly without going blind, it looks pretty, and still shows off the best parts of your landscape. 80 watts and lower are dark sky lighting approved.

Typically, medium wattage lights range from 40 to 80 watts, with 60 watts being the norm for outdoor home lighting. They're energy-efficient and produce enough light to brighten up outdoor areas. Medium wattage lights are suitable for areas where bright light is needed, but you don't want to overdo it.

Recommended Lumens for Specific Outdoor Needs

Below is a list of recommended LED lumens for specific outdoor lighting: Step lights: 12-100 lumens. Hardscape lights (on walls): 50-185 lumens. Landscape lights: 50-300 lumens.

Electrical leaks, short-circuits and electrical leaks that involve short-circuits are some of the more likely faults that occur in LED devices. Unlike faults in conventional incandescent and fluorescent lights, these faults involve short-circuits and can place a burden on the drive circuit.

One of the drawbacks of LED lighting technology is that it often has lower wattage, which reduces its efficacy. While LEDs are more energy efficient, they do not generate as much light as higher-wattage lighting solutions and may not be ideal for certain applications.

One of the most common reasons that LED bulbs burn out quickly is when they're used in incompatible dimming circuits. Firstly, remember that LED bulbs aren't dimmable by default. While you can use dimmable LED bulbs in non-dimmable circuits, the reverse is not true, so check before you install a new bulb.